What is the maximum Zs for a 63A MCB Type B?

The maximum earth fault loop impedance (Zs) for a 63A MCB Type B is 0.69Ω for 0.4s disconnection time, as listed in BS 7671 Table 41.3 of BS 7671:2018+A2:2022. For on-site testing, the measured value must not exceed 0.55Ω (80% of the tabulated value) to account for conductor temperature rise.

What is the testing limit for a 63A MCB Type B?

The testing limit is 0.55Ω. This is 80% of the tabulated maximum Zs (0.69 × 0.8 = 0.55Ω). When you measure Zs on site at ambient temperature, your reading must be at or below this value. If it falls between 0.55Ω and 0.69Ω, you can perform a more precise temperature correction calculation per IET Guidance Note 3.

What fault current is needed to trip a 63A MCB Type B within 0.4 seconds?

A 63A MCB Type B requires a minimum fault current (Ia) of 315A to guarantee tripping within 0.4 seconds. This is derived from the magnetic trip characteristic: 5 × 63A = 315A. The circuit must be capable of delivering at least this current under fault conditions, which is why max Zs is limited to 0.69Ω.

Max Zs for 63A Type B MCB

BS 7671 Table 41.3 — BS 7671:2018+A2:2022

Max Zs (0.4s)

0.69Ω

Testing Limit

0.55Ω

Max Zs (5s)

0.69Ω

Ia (0.4s)

315A

At a Glance

Device: MCB Type B — 63A
Standard: BS EN 60898
Max Zs (0.4s): 0.69Ω
Max Zs (5s): 0.69Ω
Testing Limit (80%): 0.55Ω
Ia (0.4s): 315A

About MCB Type B

Type B MCBs have a magnetic trip range of 3–5× rated current (In). They are the standard choice for domestic and light commercial circuits — lighting, socket outlets, and water heating. The relatively low trip multiplier means higher permissible Zs values compared to Type C or D, making them suitable for circuits with longer cable runs.

Typical Circuits for 63A Type B MCB

Recommended cable sizes for 63A Type B MCB circuits
Circuit	Cable Size	Notes
Sub-main to outbuilding	16mm² T&E or SWA	Distribution board sub-feed
EV charger (large)	10–16mm² T&E	22kW three-phase charger protection

Worked Example: Maximum Cable Run for 63A MCB Type B

Maximum Zs (tabulated) = 0.69Ω (BS 7671 Table 41.3)
Testing limit (80%) = 0.69 × 0.8 = 0.55Ω
Assume Ze = 0.8Ω (typical TN-S supply)
Maximum R1+R2 = 0.55 − 0.8 = —Ω
Using 16mm² T&E: R1+R2 = 2.3 mΩ/m
The available R1+R2 margin is insufficient for standard cable — verify the earthing arrangement.

The tight Zs limit for this device means cable runs must be very short. Verify the supply earthing type and consider whether a lower-rated or different device type is more appropriate.

0.4s and 5s Disconnection — Same Values for Type B

For Type B MCBs, the magnetic trip operates at 3–5× In regardless of whether the required time is 0.4s or 5s. The max Zs is 0.69Ω for both disconnection times at 63A. This means the same limit applies whether protecting a final circuit (0.4s) or a distribution circuit (5s).

63A Across Device Types

Device Type	Max Zs (0.4s)	Testing Limit
MCB Type B	0.69Ω	0.55Ω
MCB Type C	0.35Ω	0.28Ω
MCB Type D	0.17Ω	0.14Ω
BS 88 Fuse	0.54Ω	0.43Ω