What is the maximum Zs for a 16A MCB Type C?

The maximum earth fault loop impedance (Zs) for a 16A MCB Type C is 1.37Ω for 0.4s disconnection time, as listed in BS 7671 Table 41.3 of BS 7671:2018+A2:2022. For on-site testing, the measured value must not exceed 1.1Ω (80% of the tabulated value) to account for conductor temperature rise.

What is the testing limit for a 16A MCB Type C?

The testing limit is 1.1Ω. This is 80% of the tabulated maximum Zs (1.37 × 0.8 = 1.1Ω). When you measure Zs on site at ambient temperature, your reading must be at or below this value. If it falls between 1.1Ω and 1.37Ω, you can perform a more precise temperature correction calculation per IET Guidance Note 3.

What fault current is needed to trip a 16A MCB Type C within 0.4 seconds?

A 16A MCB Type C requires a minimum fault current (Ia) of 160A to guarantee tripping within 0.4 seconds. This is derived from the magnetic trip characteristic: 10 × 16A = 160A. The circuit must be capable of delivering at least this current under fault conditions, which is why max Zs is limited to 1.37Ω.

Max Zs for 16A Type C MCB

BS 7671 Table 41.3 — BS 7671:2018+A2:2022

Max Zs (0.4s)

1.37Ω

Testing Limit

1.1Ω

Max Zs (5s)

1.37Ω

Ia (0.4s)

160A

At a Glance

Device: MCB Type C — 16A
Standard: BS EN 60898
Max Zs (0.4s): 1.37Ω
Max Zs (5s): 1.37Ω
Testing Limit (80%): 1.1Ω
Ia (0.4s): 160A

About MCB Type C

Type C MCBs trip magnetically at 5–10× In. They are designed for circuits with moderate inrush current — motor-driven equipment, air conditioning, and discharge lighting. The higher trip multiplier means lower maximum Zs values, so circuit impedance must be kept tighter than with Type B devices.

Typical Circuits for 16A Type C MCB

Recommended cable sizes for 16A Type C MCB circuits
Circuit	Cable Size	Notes
Air conditioning unit	2.5mm²	Split system with compressor start current

Worked Example: Maximum Cable Run for 16A MCB Type C

Maximum Zs (tabulated) = 1.37Ω (BS 7671 Table 41.3)
Testing limit (80%) = 1.37 × 0.8 = 1.1Ω
Assume Ze = 0.35Ω (typical TN-C-S (PME) supply)
Maximum R1+R2 = 1.1 − 0.35 = 0.75Ω
Using 2.5mm² T&E: R1+R2 = 14.82 mΩ/m
Maximum cable run = 0.75 ÷ 0.01482 = 50.6m

On a TN-C-S (PME) supply with 2.5mm² cable, the maximum one-way cable run is approximately 50.6m before Zs exceeds the testing limit. In practice, always measure — parallel earth paths and cable route conditions will affect the actual value.

0.4s vs 5s Disconnection — Different Values for Type C

At 16A, the max Zs values are the same for both disconnection times: 1.37Ω.

16A Across Device Types

Device Type	Max Zs (0.4s)	Testing Limit
MCB Type B	2.73Ω	2.18Ω
MCB Type C	1.37Ω	1.1Ω
MCB Type D	0.68Ω	0.54Ω
BS 88 Fuse	2.57Ω	2.06Ω