What is the maximum Zs for a 10A MCB Type D?

The maximum earth fault loop impedance (Zs) for a 10A MCB Type D is 1.09Ω for 0.4s disconnection time, as listed in BS 7671 Table 41.3 of BS 7671:2018+A2:2022. For on-site testing, the measured value must not exceed 0.87Ω (80% of the tabulated value) to account for conductor temperature rise.

What is the testing limit for a 10A MCB Type D?

The testing limit is 0.87Ω. This is 80% of the tabulated maximum Zs (1.09 × 0.8 = 0.87Ω). When you measure Zs on site at ambient temperature, your reading must be at or below this value. If it falls between 0.87Ω and 1.09Ω, you can perform a more precise temperature correction calculation per IET Guidance Note 3.

What fault current is needed to trip a 10A MCB Type D within 0.4 seconds?

A 10A MCB Type D requires a minimum fault current (Ia) of 200A to guarantee tripping within 0.4 seconds. This is derived from the magnetic trip characteristic: 20 × 10A = 200A. The circuit must be capable of delivering at least this current under fault conditions, which is why max Zs is limited to 1.09Ω.

Max Zs for 10A Type D MCB

BS 7671 Table 41.3 — BS 7671:2018+A2:2022

Max Zs (0.4s)

1.09Ω

Testing Limit

0.87Ω

Max Zs (5s)

1.09Ω

Ia (0.4s)

200A

At a Glance

Device: MCB Type D — 10A
Standard: BS EN 60898
Max Zs (0.4s): 1.09Ω
Max Zs (5s): 1.09Ω
Testing Limit (80%): 0.87Ω
Ia (0.4s): 200A

About MCB Type D

Type D MCBs trip magnetically at 10–20× In. They handle the highest inrush currents — transformers, welding equipment, and X-ray machines. The very high trip multiplier produces very low max Zs values, which severely limits cable run lengths. Type D devices are rarely suitable for final circuits with 0.4s disconnection requirements.

Typical Circuits for 10A Type D MCB

Recommended cable sizes for 10A Type D MCB circuits
Circuit	Cable Size	Notes
X-ray equipment	1.5–2.5mm²	Very high inrush medical equipment

Worked Example: Maximum Cable Run for 10A MCB Type D

Maximum Zs (tabulated) = 1.09Ω (BS 7671 Table 41.3)
Testing limit (80%) = 1.09 × 0.8 = 0.87Ω
Assume Ze = 0.35Ω (typical TN-C-S (PME) supply)
Maximum R1+R2 = 0.87 − 0.35 = 0.52Ω
Using 1.5mm² T&E: R1+R2 = 24.2 mΩ/m
Maximum cable run = 0.52 ÷ 0.0242 = 21.5m

On a TN-C-S (PME) supply with 1.5mm² cable, the maximum one-way cable run is approximately 21.5m before Zs exceeds the testing limit. In practice, always measure — parallel earth paths and cable route conditions will affect the actual value.

0.4s vs 5s Disconnection — Significant Difference for Type D

At 10A, the max Zs values for Type D are 1.09Ω for both disconnection times.

10A Across Device Types

Device Type	Max Zs (0.4s)	Testing Limit
MCB Type B	4.37Ω	3.5Ω
MCB Type C	2.19Ω	1.75Ω
MCB Type D	1.09Ω	0.87Ω
BS 88 Fuse	4.85Ω	3.88Ω